Tubing Connectors and Fittings
Microsolv Technology Corporation Union, Connector Kits, Cross, High Pressure, 0.50mm Through Holes with 10-32 Screw Threads. Carbon PEEK, with Connector Nuts. Use with 1/16" Tubing. 2/PK.
These "Union" Kits are used to connect the same size PEEK or Stainless Steel tubing on all ends, in the high pressures zones of HPLC systems. A "Cross Connection" is often used to split flow into two or three directions or to combine two or three streams into one. Supplied with 2 Cross Unions and Four Finger Tightened Connectors (nuts). Carbon PEEK has been reinforced with carbon fiber, giving it the highest strength and stiffness of all the PEEK grades and improving its load-carrying capacity.
Microsolv Technology Corporation Tubing Connector Fittings, High Pressure, One Piece, 1/16", PEEK, Yellow, Large Combihead with 10-32 Screw Threads. Finger or wrench Tighten, 10/PK.
These all PEEK "Male Nuts" are used to connect PEEK or Stainless Steel tubing in the high pressures zones of HPLC systems. This Combihead Fitting has a partially knurled, rounded head for hand tightening and a "Flat" section of the head for using a wrench for a final quarter turn or to loosen the nut when it is tightly screwed into the fitting. This fitting has 12mm head, 22mm total length (top to bottom) with an 8mm thread length. The beveled inlet hole helps to make threading the tubing through the fitting easier. Color coded to help identify different users or columns while on an instrument.
Microsolv Technology Corporation Tubing Connector Fittings, High Pressure, One Piece, 1/16", PEEK, Green, Large Combihead with 10-32 Screw Threads. Finger or wrench Tighten, 1 EA.
These all PEEK "Male Nuts" are used to connect PEEK or Stainless Steel tubing in the high pressures zones of HPLC systems. This Combihead Fitting has a partially knurled, rounded head for hand tightening and a "Flat" section of the head for using a wrench for a final quarter turn or to loosen the nut when it is tightly screwed into the fitting. This fitting has 12mm head, 22mm total length (top to bottom) with an 8mm thread length. The beveled inlet hole helps to make threading the tubing through the fitting easier. Color coded to help identify different users or columns while on an instrument.
Microsolv Technology Corporation Tubing Connector Fittings, High Pressure, One Piece, 1/16", PEEK, Natural, Large Combihead with 10-32 Screw Threads. Finger or wrench Tighten, 10/PK.
These all PEEK "Male Nuts" are used to connect PEEK or Stainless Steel tubing in the high pressures zones of HPLC systems. This Combihead Fitting has a partially knurled, rounded head for hand tightening and a "Flat" section of the head for using a wrench for a final quarter turn or to loosen the nut when it is tightly screwed into the fitting. This fitting has 12mm head, 22mm total length (top to bottom) with an 8mm thread length. The beveled inlet hole helps to make threading the tubing through the fitting easier. Color coded to help identify different users or columns while on an instrument.
Microsolv Technology Corporation Union, Connector Kit, Cross, High Pressure, 0.30mm Through Hole with 10-32 Screw Threads. PEEK, Round with an Internal X. Use with 1/16" Tubing. 1 EA.
This low dead volume, "Union" is used to connect the same size PEEK or Stainless Steel tubing on both ends, in the high pressures zones of HPLC systems. A "Cross Connection" is often used to split flow into two or three directions or to combine two or three streams into one. Supplied with Four Finger Tighten Connectors (nuts).
Microsolv Technology Corporation Tubing Connector Fittings, High Pressure, Two Pieces, 1/16", PEEK, Natural, Small Hex Head, Short Length and 10-32 Screw Threads. Use with Double Cone Ferrules. Wrench Tighten, 10/PK.
These Two Piece, "Male Nuts" are used to connect PEEK or Stainless Steel tubing in the high pressures zones of HPLC systems. This fitting has a 7mm diameter knurled head, 11mm total length (top to bottom), 7mm Thread Length and requires a Double Cone Ferrule, sold separately. 2 Piece Male Nuts are often chosen because they can be used at slightly higher pressures compared to 1 Piece Nuts. The required, Single Coned Ferrules will swage tubing grip it and not spin as you turn the Nut. As Ferrules wear down, they need to be replaced. This Nut can be reused with new Ferrules.
Microsolv Technology Corporation Tubing Connector Fittings, High Pressure, Two Pieces, 1/16", PEEK, Natural, Small Hex Head, Standard Length and 10-32 Screw Threads. Use with Single Cone Ferrules. Wrench Tighten, 1 EA
These Two Piece, "Male Nuts" are used to connect PEEK or Stainless Steel tubing in the high pressures zones of HPLC systems. This fitting has a 7mm diameter knurled head, 15mm total length (top to bottom), 11mm Thread Length and requires a Single Cone Ferrule, sold separately. 2 Piece Male Nuts are often chosen because they can be used at slightly higher pressures compared to 1 Piece Nuts. The required, Single Coned Ferrules will swage tubing grip it and not spin as you turn the Nut. As Ferrules wear down, they need to be replaced. This Nut can be reused with new Ferrules.
Microsolv Technology Corporation Union, Connector, Cross, High Pressure, 0.30mm Through Hole with 10-32 Screw Threads. PEEK, Round with an Internal X. Use with 1/16" Tubing. 1 EA.
This low dead volume, "Union" is used to connect the same size PEEK or Stainless Steel tubing on both ends, in the high pressures zones of HPLC systems. A "Cross Connection" is often used to split flow into two or three directions or to combine two or three streams into one.Use with Two Finger Tighten Connectors (nuts).
Chemglass Life Sciences Y Connector with Male Luer Lock, L/S Platinum Cured Silicone Pump Tubing, 1/8" ID x 1/4" OD Size 16
Reduces set up time and minimizes labor cost. Y connector and male luer assembly are package 10 per bag and ready to use.Manufactured with 5' of No.16 (1/8 x 1/4') platinum cured silicone tubing.For sterile applications the assembly can be safely autoclaved.
Microsolv Technology Corporation Tubing Connector Fittings, High Pressure, One Piece, 1/16", PEEK, Red, Large Combihead with 10-32 Screw Threads. Finger or wrench Tighten, 10/PK.
These all PEEK "Male Nuts" are used to connect PEEK or Stainless Steel tubing in the high pressures zones of HPLC systems. This Combihead Fitting has a partially knurled, rounded head for hand tightening and a "Flat" section of the head for using a wrench for a final quarter turn or to loosen the nut when it is tightly screwed into the fitting. This fitting has 12mm head, 22mm total length (top to bottom) with an 8mm thread length. The beveled inlet hole helps to make threading the tubing through the fitting easier. Color coded to help identify different users or columns while on an instrument.
AVANTOR MASTERFLEX (VWR LLC) CPC (Colder) HFC22612 Quick-disconnect fittings, Straight-through hose barbs inserts, PP, 3/8""
High-flow quick-disconnect couplings consists of a body and an insert (order fitting halves separately). Plug insert into coupling body to connect¿fitting halves lock into place immediately. To disconnect fitting halves, simply press the button on the coupling body. Valved models have a spring-operated 316 SS valve that seals the flow path when fitting halves are disengaged. All fitting bodies have 316 SS latch springs and EPDM seals.
